|
From 1929〔Thomas Parke Hughes ''Networks of power: electrification in Western society, 1880-1930'' JHU Press, 1993 ISBN 0-8018-4614-5 page 376〕 to the late 1960s, large alternating current power systems were modelled and studied on AC network analyzers (also called alternating current network calculators or AC calculating boards) or transient network analyzers. These special-purpose analog computers were an outgrowth of the DC calculating boards used in the very earliest power system analysis. By the middle of the 1950s, fifty network analyzers were in operation.〔Charles Eames, Ray Eames ''A Computer Perspective: Background to the Computer Age'',Harvard University Press, 1990 0674156269, page 117〕 AC network analyzers were much used for power flow studies, short circuit calculations, and system stability studies, but were ultimately replaced by numerical solutions running on digital computers. While the analyzers could provide real-time simulation of events, with no concerns about numeric stability of algorithms, the analyzers were costly, inflexible, and limited in the number of buses and lines that could be simulated.〔M.A. Laughton, D.F Warne (ed),''Electrical Engineer's Reference Book (16th Edition)'', Elsevier, 2003 ISBN 978-1-60119-452-7 pages 368-369〕 Eventually powerful digital computers replaced analog network analyzers for practical calculations, but analog physical models for studying electrical transients are still in use. == Calculating methods == As AC power systems became larger at the start of the 20th century, with more interconnected devices, the problem of calculating the expected behavior of the systems became more difficult. Manual methods were only practical for systems of a few sources and nodes. The complexity of practical problems made manual calculation techniques too laborious or inaccurate to be useful. Many mechanical aids to calculation were developed to solve problems relating to network power systems. DC calculating boards used resistors and DC sources to represent an AC network. A resistor was used to model the inductive reactance of a circuit, while the actual series resistance of the circuit was neglected. The principle disadvantage was the inability to model complex impedances. However, for short-circuit fault studies, the effect of the resistance component was usually small. DC boards served to produce results accurate to around 20% error, sufficient for some purposes. Artificial lines were used to analyze transmission lines. These carefully constructed replicas of the distributed inductance, capacitance and resistance of a full-size line were used to investigate propagation of impulses in lines and to validate theoretical calculations of transmission line properties. An artificial line was made by winding layers of wire around a glass cylinder, with interleaved sheets of tin foil, to give the model proportionally the same distributed inductance and capacitance as the full-size line. Later, lumped-element approximations of transmission lines were found to give adequate precision for many calculations. Laboratory investigations of the stability of multiple-machine systems were constrained by the use of direct-operated indicating instruments (voltmeters, ammeters, and wattmeters). To ensure that the instruments negligibly loaded the model system, the machine power level used was substantial. Some workers in the 1920s used three-phase model generators rated up to 600 kVA and 2300 volts to represent a power system. General Electric developed model systems using generators rated at 3.75 kVA.〔H.P. Kuehni, R.G. Lorraine, ''A New A-C Network Analyzer'', ''Transactions AIEE'', February 1938 volume 57 page 67〕 It was difficult to keep multiple generators in synchronism, and the size and cost of the units was a constraint. While transmission lines and loads could be accurately scaled down to laboratory representations, rotating machines could not be accurately miniaturized and keep the same dynamic characteristics as full-sized prototypes; the ratio of machine inertia to machine frictional loss did not scale.〔David A. Mindell, ''Between Human and Machine: Feedback, Control and Computing Before Cybernetics'', JHU Press, 2004 ISBN 0801880572 pp.149-150〕 抄文引用元・出典: フリー百科事典『 ウィキペディア（Wikipedia）』 ■ウィキペディアで「Network analyzer (AC power)」の詳細全文を読む スポンサード リンク
|